Over 10 years professional experience on electric fireplaces & home lighting products

How to correctly using modern fireplace?

by:Longjian     2020-10-21
The first step: check is whether the throttle open the throttle device is used to control the air flows through the flue. Flue is the chimney in the channel or pipe for flue gas emissions. Air door through the joystick to control, usually a direction is opened, is closed in the opposite direction. Before lighting the fireplace, please make sure the door is open, otherwise, the smoke will flow backward into the room. At the same time, open the throttle when the ignition is more easier. Confirm the state of the air door is opened, lighting the fireplace is the first step is ready. The second step: if the fireplace is a glass door closed fireplace, please ensure that the glass door have 30 minutes before lighting the fireplace time open, in order to make the fireplace at room temperature. Because of the cold air is heavier than warm air, if the air is relatively too cold outside, so the cold air can form a stream of air flow into the fireplace. Open fireplace can make indoor warm air rises into the chimney, and form a strong updraft enough to prevent cold air intrusion. The second step: if the fireplace is a glass door closed fireplace, please ensure that the glass door have 30 minutes before lighting the fireplace time open, in order to make the fireplace at room temperature. Because of the cold air is heavier than warm air, if the air is relatively too cold outside, so the cold air can form a stream of air flow into the fireplace. Open fireplace can make indoor warm air rises into the chimney, and form a strong updraft enough to prevent cold air intrusion. Step 3: check the smoke crossing of the airflow in the fireplace lit a match or other similar fire, observe the airflow are rising or falling, if the air is still falling, so should use the appropriate method to change the flow of air, the air down, it's difficult to ignite one way is to use some kind of kindling, These kindling should has the characteristics of anthracite) To preheat the hearth, help the formation of updraft. Can be according to the following steps: 1 closed throttle, prevent cold air flows downward. 2 kindling on furnace shovel, and exports the near the fireplace flue, purpose is to heat the upper part of the fireplace. 3 feeling about open the throttle slowly see if air flow upward mobility, if not to repeat the previous steps. Step 4: ignition's note 1 the kindling on fire grate at the bottom of the lower part, piled up over the grate combustible kindling material 2 is used to ignition of the material, usually easily ignited material, sometimes people use newspaper, branches and so on proper kindling. When light the kindling, should be able to burn to light the combustible material piled up at the top. 3 don't use too much paper kindling, because it can produce a lot of smoke. 4 attention to flammable materials flat, when the stack to leave enough space for air flow. 5 layered cross stacked into pyramid shape would be better 6 in relatively large pieces of flammable materials placed around a few small pieces of wood, the biggest combustible substance cannot be more than the ordinary people of the upper arm. Smaller easier to ignite the combustible material and can form better ash layer. 7 the internal space highly flammable materials stacked up to the fireplace 2/3 position. Step 5: light the kindling. In half an hour before, to pay more attention to the status of smoke. 1 if the black smoke from the chimney, the oxygen supply is insufficient, using the furnace check carefully adjust the heap of combustible material, pick the combustible material pile up a little, the aim is to get the bottom of the heap more air into the flammable materials. If too high at the bottom of the charcoal, charcoal formation of ash heap stand even some, leave more space for the flow of the air. If the smoke is gray, suggesting that did not make full combustion of combustible material, but along the flue, it may be that: 1) No flash from above. 2) Combustible material might be a little wet. 3) Too much oxygen supply. This is confusing, have delicate balance relationship between air and fuel, if too much oxygen, things are difficult to capture the flame fuel formation, it will produce more smoke. Step 6: open the window a little bit if after lighting the fireplace airflow adverse flow, still have the inside the smoke entering the room, can try to open the window a few centimeters. If the position of the window is in the wall opposite the fireplace, the effect will be better. But if someone in the position of the fireplace and window between, could feel the cool wind, because the fireplace will be sucked through the air, the cold air will blow out of the window to the body, this is the best away from this area. Step 7: join big combustible substance correct pile can make fire continued for a period of time without the need for further care, when the flame into a good state, you can see under the flame burning of combustible material in flashing, temperature has been very hot, you can carefully put larger combustible substance in the top, try to keep combustible material still have good shape, bigger combustible material need a certain amount of time to start burning, once they began to burn, will last a long time, does not require the intervention of people, burning charcoal will heat, for a long time for you to enjoy the warm and comfortable. Step 8: put out the fireplace before leaving the room for half an hour to combustible material, using the fireplace hooks will still spread out in the chamber of a stove or furnace burning combustible substances, the smaller the combustible material, the easier it is consumed. Confirm that the fire has gone out, shut off the throttle, such indoor temperature will remain for a long time.
Custom message
Chat Online 编辑模式下无法使用
Chat Online inputting...